Project Description

corrugated carton machine production line

Whatapp:  +86-13801968812

Email: greatsuccess@gigalx.com

LXC-1500H Hydraulic Mill Roll Stand

Control type: whole hydraulic type Characteristic

*   Symmetry structure could install two bundles real paper at the same time, and change the paper without any stop.

*   Adopt hydraulic drive that could make the real paper lift-lower, clamp and release and move.

*   Adopt pneumatic strain to adjust the real paper.

*   Expanding clips design.

*   Tension control by pneumatic brake system, manual controlled and also can be controlled by splicer.

LX-1100  Pre-heater

(Model:600/900/1000/1100 S/D/T/Q)

The maximum paper width: 2500MM.

*  Pass the national pressure vessel inspection, and get a safe certification about national pressure vessel security;

*  One is fixed, another one free to move, both of them are steel products.

*  Warm-range adjustment adopts electric control.

*  Power motor 1/2HP gear with a turbine and a drive arm with gear transmission.

*  The preheated rollers are electrically rotating, with reducing motor and single ball bearing can set idle running with stable speed.

 
LXC-320SN/360S Single Facer
Flute type: as per customer’s requirements, A/C/B/E/F etc;
Design-corrugating roller under pressure roller, helps lowering machine’s center and reducing shaking;
Inner suction structure of corrugating roller;
Separate transmission for gluing unit, its whole structure is movable, easy to clean and maintenance;
Inlet and outlet of steam is fixed joint.
Design speed:180/200 m/min
Available width:1400mm,1600mm,1800mm,2000mm,2200mm
Corrugated roller made of CR-MO alloy steel No.48
LXC-2B Single/Double Decks Feeding Bridge

Available width: 1400 – 2500 mm

*    Adopt suction tension and its adjusting device,  assure the sticking and stable  paperboard pass by of the heating plate

*    Motorized alignment adjustment, easy and swift

*    Two set of operation panels, make easy adjustment up or down the bridge

*    Synchronous motor driving, with high and low speed stacking device, to transport  and stack the corrugated paperboard.

 
“LXC-318D Glue Machine(High Speed)

Main specification:
Working width: 1400-2500mm
max working speed: 200mm/min,
Glue roller dia.: 318-2 PCS
Steel pipe material, netty hard Chrome. Treatment.
Steel material (S45C) with hard chrome Treatment.

LXC-745N Steam-heating & Press-cooling System
LXC-745N-D Driving RollerTechnical specification:
1. Availbale width: 1400-2200mm
2. Design speed: 200m/minStructure characteristic:
1. Whole body is high strength channel steel, stable, beautiful, suitable for high speed machinery running.
2. Heating plate is made according to national container safety standard, of 600mm steel. Inside, S type construction will raise the steam usage efficiency. More welded rods will keep heating plate unchanged in shape.
3. Heating section is tense pressure roller structure, cardboard sticks firmly and levels off.
 
  LXC-250N NC Thin Blade Slitter Scorer

(LXC-160N 180N 200N 250N)

Technical parameter:

Blade configuration: 5 blades 8 scores(or according to customer’s requirement)

— AC servo motor by Mitsubishi of Japan;

-Computerized system can grind the blades automatically (without braking). Time and frequency of grinding can be self-set by customer according to working conditions

-Computer monitoring to guarantee synchronization with whole line

LXC-150/180 Double Layer NC Cutoff with Rotary Blade

Avaliable width:1400-2200mm
Design speed:180m/min
Cut length:Max.9999mm Min.500mm
Precision(in steady speed):±1mm
* Special structural design, strength and
excellent mechanical wall panels and the base
wall panels on both sides of a perspective
window, easy to observe and maintenance.
* Transmission system adopts the automatic
cycle lubricating oil pump, to ensure
transmission accuracy.